Woven vs Knit Fabric: The Difference and When It Matters

White woven cotton shirting and grey knit jersey lying side by side,   the woven corner folded flat and the knit corner rolling.

Woven fabric is made by interlacing two sets of yarn at right angles on a loom. Knit fabric is made by looping one continuous yarn through itself. That single difference in construction is what decides whether a fabric stretches, whether it frays, how you cut it and how a garment made from it behaves after a year of wear.

 

Everything else people say about woven versus knit follows from those two structures. This guide covers both, the third category that gets left out of the comparison, and what the difference means once you are labelling and finishing the garment.

 

The short answer

 

Woven fabric is stable and knit fabric stretches. A woven is built from warp yarns running the length of the fabric and weft yarns crossing them, locked together at every intersection. A knit is built from rows of loops, and a loop can open and close, which is where the stretch comes from.

 

Woven fabric Knit fabric
Construction Two yarn sets interlaced at 90 degrees One yarn looped through itself in rows
Stretch Very little, unless elastane is added Built in, in one or both directions
Cut edge Frays and needs finishing Curls but does not unravel at the cut
Drape Holds a shape and a crease Follows the body
Wrinkling Creases and holds the crease Springs back
Typical garments Shirts, jeans, suiting, outerwear T-shirts, jersey, sweatshirts, socks
Sewing Straight stitch, standard presser foot Stretch stitch or overlocker, ballpoint needle

 

In prose, for anyone scanning: a woven fabric is interlaced and stable, frays when cut, holds a crease and suits structured garments. A knit fabric is looped and stretchy, curls rather than frays, springs back from wrinkles and suits garments that move with the body.

 

How woven fabric is made

 

A woven fabric comes off a loom, where lengthwise warp yarns are held under tension and a crosswise weft yarn passes over and under them. Every crossing point is a lock, which is why the fabric barely moves in either direction.

 

The pattern of over and under is the weave, and it changes the character of the cloth more than the fibre does.

 

  • Plain weave. One over, one under, the simplest possible structure. Poplin, chambray and canvas are plain weaves. Strong, flat, and the same on both faces.
  • Twill weave. The weft passes over two or more warps and steps across on each row, which produces the diagonal line you can see on denim and chino.
  • Satin weave. Long floats of yarn on the surface, which is what gives satin its sheen and its smooth hand.
  • Jacquard and damask. The pattern is built into the structure rather than printed on it, so the design is the fabric. This is the construction Super Label Store uses to weave brand labels.

 

Woven fabric has a grain: lengthwise along the warp, crosswise along the weft, and on the bias at 45 degrees. The bias is the only direction a plain woven gives in, which is why bias cut dresses drape the way they do.

 

Diagram of woven fabric structure with warp yarns crossing weft yarns at right angles.

 

How knit fabric is made

 

A knit fabric is built from loops, and the loops are what stretch. One yarn runs through a row, each loop catching the loop in the row below it, so pulling the fabric lets every loop elongate slightly and the whole piece gives.

 

There are two families, and they behave differently enough to matter.

 

Weft knits are made across the fabric, one row at a time, which is what a hand knitter does and what most jersey machines do. Single jersey, rib, interlock and French terry are weft knits. They stretch a lot, mostly crosswise, and a cut or a broken yarn can run down the fabric in a ladder.

 

Warp knits are made down the fabric, with many yarns looping in parallel. Tricot and powernet are warp knits. They stretch less, run far less readily, and turn up in activewear, linings and lingerie.

 

AFBEELDING 3, hier plaatsen. GEEN AI, zelfde reden als afbeelding 2.   Een getekend diagram van de lussenstructuur: rijen lussen die door de lus   eronder haken, met de V-vorm aan de voorkant zichtbaar. Idealiter in dezelfde   stijl en hetzelfde formaat als afbeelding 2, zodat de twee naast elkaar leesbaar   zijn. Alternatief: een macro-opname van een stuk single jersey.   Alt-tekst: Diagram of knit fabric structure showing rows of interlocking loops.

 

Stretch: the difference you feel first

 

A plain woven fabric gives about 2 to 3 percent, a single jersey gives 25 to 50 percent across the fabric, and a rib knit can give more than 100 percent. That range is the practical reason the two are not interchangeable in a pattern.

 

A garment pattern is drafted for one or the other. A knit pattern has negative ease, meaning the piece is cut smaller than the body and the fabric stretches to fit. A woven pattern has positive ease, with room built in, plus darts, pleats or gathers to shape flat cloth around a body. Cutting a knit pattern from a woven gives you something you cannot get into, and cutting a woven pattern from a knit gives you something shapeless.

 

Woven fabric can be given stretch by adding elastane to the yarn. A shirting with 2 to 3 percent elastane moves enough to be comfortable while staying a woven in every other respect: it still frays, still creases and still holds its shape.

 

Cutting and sewing: what actually changes

 

Woven fabric is the easier one to sew and the harder one to fit. Knit fabric is the opposite.

 

Woven Knit
Needle Sharp Ballpoint or stretch, so it slips between loops
Stitch Straight stitch holds Zigzag, stretch stitch or overlocker, so the seam gives
Seam finish Needed, or the edge frays Optional, the edge will not unravel
Cutting Cut on grain, the piece stays put Let it relax first, it stretches under its own weight
Seam allowance Usually 0.6 in (15 mm) Usually 0.25 to 0.4 in (6 to 10 mm)

 

Put simply: on a woven you need a sharp needle, a straight stitch and a finished edge; on a knit you need a ballpoint needle, a stitch that stretches, and patience while cutting.

 

The mistake that costs most beginners a garment is sewing a knit with a straight stitch. The seam holds right up until the wearer pulls it over their head, and then the thread snaps because the fabric stretched and the stitching could not.

 

Fraying and edges

 

Woven fabric frays and knit fabric curls. Cut a woven and the loose yarn ends at the edge work free with every wash, which is why a raw seam in a woven garment has to be overlocked, bound, French seamed or pinked.

 

Cut a knit and nothing unravels, because the loops hold each other rather than being held by a weave. A single jersey will roll towards the right side at the edge, which is cosmetic rather than structural, and a cut end on a weft knit can ladder if a loop is broken.

 

That difference carries over to anything you attach. A woven label is a tiny piece of woven fabric, so its cut edges would fray in exactly the same way. Super Label Store seals them with Heat Cut edges for that reason, which is also why a woven label keeps a clean edge long after the garment has been washed a hundred times.

 

Woven, knit and nonwoven

 

Nonwoven is the third category, and it has neither interlacing nor loops. The fibres are bonded directly into a sheet by heat, pressure, chemicals or needle punching, with no yarn involved at all.

 

The comparison between woven and nonwoven fabrics usually comes up because nonwoven is everywhere in garment construction without being visible: fusible interfacing in a collar or a waistband, the inner layer of a structured cap, felt, and most disposable products.

 

Woven Knit Nonwoven
Built from Interlaced yarns Looped yarn Bonded fibres, no yarn
Stretch Minimal High Little, and it tears rather than gives
Grain Yes Yes, along the rows None
Reuse Long life Long life Usually short life

 

The quick version: woven and knit fabrics are made from yarn and last the life of a garment, while nonwoven is made from loose fibres bonded into a sheet and usually plays a supporting or disposable role.

 

Three swatches side by side showing woven canvas, knit jersey and nonwoven interfacing.

 

Knit elastic versus woven elastic

 

The same distinction runs through elastic, and it changes which one belongs in a waistband.

 

Woven elastic is the firm one. It keeps its width when stretched and survives being sewn through, which makes it the choice for a waistband casing on trousers and skirts, and for anything carrying weight.

 

Knit elastic is softer and lighter. It narrows slightly when stretched, it is comfortable directly against skin, and it suits lightweight fabrics, sleeves and underwear. Sewing through it is fine.

 

Braided elastic is the third type people meet: it narrows considerably when stretched and loses its stretch if you sew through it, so it belongs inside a casing.

 

If you are choosing between knit elastic and woven elastic for a waistband that has to hold, take woven. If it sits against skin on a light garment, take knit.

 

Which garments use which

 

Woven Knit
Shirts and blouses T-shirts and jersey tops
Jeans, chinos, tailored trousers Sweatshirts and hoodies
Suiting and blazers Leggings and activewear
Coats and structured outerwear Socks, underwear, swimwear
Bags, caps, aprons, workwear Knitwear, ribbing, cuffs and collars

 

Most garments use both. A sweatshirt is a knit body with knit ribbing at the cuffs, and a shirt is a woven body with a woven collar stand and a nonwoven interfacing inside it.

 

Labelling a knit versus labelling a woven

 

The construction of the garment decides how the label attaches, and this is where the difference stops being theoretical.

 

On a woven garment almost everything works. The fabric is flat, stable and heat tolerant, so a sew-on label, an iron-on label or a combination backing all hold. A shirt, a denim jacket or a canvas bag takes any of the three.

 

On a knit, sew-on is the one to choose. Two reasons, and both come from the loops. Heavy knits and fleece have a textured surface, so an adhesive backing meets the high points of the pile rather than a continuous field of fibres, and the contact area is a fraction of what it looks like. And knit fabric moves, while set adhesive does not, so a bond on a stretch fabric works loose at the edges over time.

 

Placement matters more on a knit too. A label sewn flat across a stretchy panel creates a stiff patch that the fabric has to work around, and over time that shows. Sewing the label into a stable area instead keeps the fabric free to move around it. On a jersey t-shirt that means an end fold label stitched flat against the existing neck tape, which is what almost every manufactured garment uses, because a coverstitched jersey neckline has no open seam to catch a centre fold in. A woven shirt does have that seam, which is why the centre fold belongs there instead.

 

Super Label Store weaves labels in damask from 5 pieces per design, in any size from 0.4 x 0.4 in (10 x 10 mm) to 11.8 x 11.8 in (300 x 300 mm), with sew-on, iron-on or combination backing chosen per order. If you are labelling knitwear, jersey or activewear, pick sew-on and a fold that lets the label sit in a seam. The full specification is on the custom woven labels page.

 

How to tell what you are holding

 

Pull it crosswise. A woven barely moves. A knit gives immediately and springs back.

 

Look at the surface closely. A woven shows a grid of yarns crossing at right angles. A knit shows rows of interlocking V shapes on the face and horizontal ridges on the back.

 

Look at a cut edge. A woven sheds loose yarn ends. A knit curls towards one side and stays intact.

 

Crush a corner in your hand. A woven holds the creases when you let go. A knit comes back almost flat.

 

Frequently asked questions

 

What is the difference between woven and knit fabric?

Woven fabric is made by interlacing two sets of yarn at right angles on a loom, which locks the structure and leaves almost no stretch. Knit fabric is made by looping one yarn through itself in rows, and because a loop can open and close, the fabric stretches. Everything else, from fraying to drape to which needle you use, follows from that.

 

What is woven fabric?

Woven fabric is cloth built on a loom from lengthwise warp yarns and crosswise weft yarns that pass over and under each other. The pattern of over and under is the weave: plain, twill, satin or jacquard. Woven fabric has a grain, frays when cut and holds a crease.

 

What is knit fabric?

Knit fabric is cloth built from rows of loops rather than crossed yarns. Weft knits such as jersey and rib are made across the fabric one row at a time and stretch a lot. Warp knits such as tricot are made down the fabric and stretch less.

 

Is knit or woven better?

Neither, and the question is really which one suits the garment. Take woven for structure, crisp edges and a shape that holds, which means shirts, jeans, tailoring and bags. Take knit for movement and comfort against the body, which means t-shirts, sweatshirts, activewear and socks.

 

Does woven fabric stretch?

A plain woven gives about 2 to 3 percent, which is barely noticeable, and the only direction it really moves is on the bias at 45 degrees to the grain. Adding elastane to the yarn gives a woven useful stretch while it stays a woven in every other way.

 

How can I tell if a fabric is knit or woven?

Pull it crosswise. A knit gives straight away and springs back; a woven barely moves. Then look at a cut edge: a woven sheds loose yarn ends, while a knit curls to one side without unravelling.

 

What is the difference between woven and nonwoven fabric?

Woven fabric is made from yarns interlaced on a loom. Nonwoven has no yarn at all: loose fibres are bonded into a sheet by heat, pressure, chemicals or needle punching. Nonwoven has no grain, little stretch, and in garments it mostly appears as fusible interfacing, cap structure and felt.

 

What is the difference between knit elastic and woven elastic?

Woven elastic is firm, keeps its width when stretched and can be sewn through, which makes it right for waistbands and anything carrying weight. Knit elastic is softer, narrows slightly under tension and sits comfortably against skin, which suits lightweight garments and sleeves.

 

Can you sew a knit on a normal sewing machine?

Yes, with two changes. Use a ballpoint or stretch needle so it slips between the loops instead of piercing them, and use a stitch that gives, such as a narrow zigzag or a built in stretch stitch. A straight stitch on a knit holds until the garment is stretched and then the thread breaks.

 

Which label backing works on knit fabric?

Sew-on. A knit surface is textured, so adhesive meets the high points of the pile rather than a flat field of fibres, and the fabric keeps moving while a set adhesive does not. Super Label Store supplies sew-on, iron-on and combination backings on the same woven label, and sew-on is the one that holds on jersey, fleece and knitwear.